neoVI FIRE 3 Specifications
Networks / Inputs
- 16 x Dual wire CAN (all baud rates supported)
- 14x Dedicated Classical CAN / CAN FD
- 2x switchable to SW CAN, LSFT CAN, or LIN
- 8x LIN / K Line / KW2K / ISO 9141
- 6x Dedicated LIN
- 2x switchable to SW CAN, LSFT CAN, or LIN
- 3x Ethernet Interfaces
- 2x RJ-45s available directly on the neoVI FIRE 3 device
- 1x RJ-45 port additionally available when utilizing provided adapter cable at 100 Mbps
Device Specifications
- Low power consumption
- Comatose: 500 microamps
- Fast wake: 70 milliamps
- Power supply: 5-60V operation
- LEDs: 10 programmable tri-color LEDs
- 2 LEDs for legacy status; 2 user buttons
- Temperature range: -40°C to +85°C
- On-board UPS for safe shutdown of data logger
- Dimensions: 60cm by 11.22cm by 3.97cm
- LEDs (user programmable): 10 programmable tri-color LEDs
- SD card: 2 card slot support for up to 2 TB of storage; card
- formatted using FAT32 for PC compatibility
- DAQ Ethernet
- Vehicle connectors: 26-pin male HD D-sub
- One-year limited warranty
- Field-upgradeable flash firmware
- General purpose I/O: 4 MISC IO (0-40V); can be configured as analog/PWM IO
- General purpose I/O rate report interval: 10 Hz to 1 kHz, or based on digital change
- USB host for RAD-IO2 or neoVI MIC2
- Standalone mode for use in scripting, receiving messages, transmitting messages, expressions, I/O and transport layers
- J2534 and RP1210 A/B compatible for CAN / ISO15765- 2:2016 (CAN FD)
- Battery-backed real-time clock (RTC)
Timing Specifications
- 64-bit timestamping to an accuracy of 25 nanoseconds on all networks
- Simultaneous operation on all CAN/LIN networks
- Transmit message double-buffering on all networks, allowing back-to-back message transmission
Network Specifications – CAN
- 16 x ISO CAN FD channels
- CAN 0B compatible for all CAN networks
- 16 dedicated ISO 11898 Dual Wire CAN FD physical layers (TJA1043)
- LSFT CAN mode: 2 Low Speed Fault Tolerant CAN physical layers (TJA1055)
- SW CAN mode: 2 Single Wire CAN physical layers GMW3089/SAE J2411(MC33897)
- Listen-only mode support
Network Specifications – LIN / K Line / KW2K / ISO 9141
Up to 8x LIN (Local Interconnect Network)
- Full support for LIN X, 2.X and J2602
- LIN J2602 / X compatible physical layer
- Software-enabled 1K LIN Master Resistor per channel
- LIN Bus Monitor Mode identifies errors: Sync Break Error State and Length, Sync Wave Error, Message ID parity, TFrameMax/ Slave Not Responding, Checksum Error and Transmit Bit Errors
- LIN Bus Master Mode operates at same time as LIN Bus Monitor
- LIN Bus Slave simulation, with or without an LDF file
- LIN Bus hardware schedule table with support for LIN diagnostics
- Initialization Waveforms, including Fast Init, Five Baud, and Custom
- Software-selectable baud rateInitialization Waveforms, including Fast Init, Five Baud, and Custom
- Software-selectable baud rate
Ordering Information
| Part Number | Description |
| NEOVI-FIRE3 | neoVI FIRE 3 Vehicle Interface, Gateway and Data Logger |
Specifications subject to change; please contact Intrepid for the latest information. All trademarks are the property of their respective owners.
